What're your insights and beliefs about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately hard job. If the old bathtub is easily easily accessible, the job can relocate quickly; if you have to open a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and set in the new one. See to it you have actually certified yourself for the job and are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This post will help you install a brand-new tub in your shower room if you have currently bought a brand-new tub as well as don't need to change the plan of your previous water system pipes.
Your devices and material checklist should consist of the following:
Planning for the Setup
First of all, the supporting frame provided with the bath must be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be rather bothersome due to the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the bathtub in the called for position. The wooden boards are valuable in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub up until the level checks out level.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; after that do the exact same for the other tap.
Turn on the supply of water and also inspect all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the bathtub must wait until the bath tub has been made use of a minimum of once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washers remain in area between the tap as well as the sink. Protect the faucet in position with the maker supplied backnut. When the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The previous kind needs to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, creating the water to permeate the wall in between the bath as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture rather early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our excerpt about Tools You Need to Install a New Bathtub . Thank you for finding the time to read our post. If you please take the time to distribute this content if you enjoyed reading it. We love reading our article about Tools You Need to Install a New Bathtub .
Ready to assist.